Overview The JM20330 is a single chip solution for serial and parallel ATA translation. It includes the Serial ATA PHY, Link, Transport, and Parallel ATA (application layer) controller. The Serial ATA physical, link, and transport layers are compliant to Serial ATA 1.0 JM20330 supports a 1.5GHz data rate, and scalable to 3.0 GHz data rate by directly doubling the internal clock source. The application layer supports both the ATA register command set and PACKET command set, which could drive both Hard Disk Drive and ATAPI Optical Storage such as CR-ROM, CD-RW, DVD-ROM, DVD-RW, etc. The Serial ATA and the Parallel ATA application layer support both host and device operation and can be configured through a single pin. Feature Compliance Serial ATA 1.0 Specification compliant Overall ... Less

Two-Way IDE To SATA + SATA To IDE Converter Two-Way IDE To SATA + SATA To IDE Converter This is a bi-direction IDE an SATA converter for serial and parallel ATA translation. You may connect an IDE hard drive to your PC motherboard's SATA controller or vice versa with this Bi-Directional IDE to SATA Converter or SATA to IDE adapter! It's easy to install and there are no drivers needed. There is a mode switch for selecting this device to be used for either SATA to IDE or IDE to SATA conversion. This IDE/SATA adapter is featured with high speed 150 MB/s transfer rate, automatic SATA 3.0/1.5 Gbps speed negotiation, and support for 3.5-inch IDE hard drives as well as 5.25" optical drives . Jmicro JM20330 Chipset Plug & Play and Hot-swapping capability 150MB/s transfer rate Automatic SATA... Less

Lindy IDE Converter for SATA Drives Plugs directly into a SATA drive 40 Way IDC Male (controller) to Serial ATA (drive) Power adapter cable included Supports SATA Generation 1 and 2 devices at speeds of 1.5 and 3GBps Fully compliant with SATA II 1.0 specification Supports HDD larger than 137GB Bridge converter supports PC, Mac and Linux Compatible with Ultra ATA 133/100/66/33 Plug & Play installation, no software required Dimensions: 75 x 26mm

Type: SATA to IDESpecifications : SATA II 3Gbps Mini Adapter Board (size 75mm x 26mm)Features: Convert the High Capacity SATA II 3Gbps and SATA 1.5Gbps devices like Blu-ray Disc optical drive SSD Hard Drive and SATA Storage Device to work with IDE Host Controller Supports any type of SATA II 3Gbps and SATA I 1 5Gbps Device (Blu-ray Disc SSD DVD DVD-RAM CD-ROM CD-RW Hard Disk) Convert SATA Drive like a standard IDE/ATAPI Drive 48 bits LBA can Break Capacity-Limit to Support HDD larger than 137GB Compliant with Serial ATA 2.6 Support Jumper setting for IDE Master Slave and Cable Select Modes Tag Command Queuing (Max 32 entries) SATA Hot-plug SATA Power Save modes ATA/ATAPI PIO mode data transfer ATA/ATAPI UDMA data transfer rate of 150 133 100 66 44 33 ... Less

Brand New IDE to SATA or SATA to IDE Bidirectional Adapter FEATURES: Converts Serial ATA to Parallel ATA Converts Parallel ATA to Serial ATA Supports ATA 100/133 Compliant with Serial ATA Specification (1) 40 pin IDE Port (1) Serial ATA Port (1) 4 Pin Power Connector

Providing Excellent Service Since 1989 STARTECH.COM ide to SATA drive mounted adapter New-Retail Description: The perfect solution for adding SATA drives to motherboards lacking available SATA connectivity, while preserving space within the computer. Also ideal for use with older motherboards that do not provide SATA data or power connectors. IDE2SAT is a pure hardware solution and requires no drivers or software and is easy to install. Features: 48 bit addressing supports larger capacity drives

NEW Startech.com IDE2SAT25 IDE 40 pin Female/SATA Adapter number: IDE2SAT25, UPC: 065030832779) Manufacturer: StarTech.com Manufacturer Part Number: IDE2SAT25 Brand Name: StarTech.com Product Model: IDE2SAT25 Product Name: 40 Pin Female IDE to SATA Adapter Converter This IDE to SATA adapter converts a 40-pin IDE connector to a SATA connector, allowing you to connect a 2.5in or 3.5in SATA (SATA, SATA II/SATA 300) drive to the motherboard in place of an IDE drive. The IDE to SATA Adapter is suitable for installation in any computer case, as it is requires minimal space and does not impact airflow. Product Type: Data Transfer Adapter Technical Information Connector on First End: 1 x 40-pin IDC Female Connector on First End: 1 x SP4 Male Connector on Second End: 1 x 7-pin Male SATA Physical... Less

Features Supports IDE with data transfer rate up to 66/100/133MB/s Serial ATA To IDE Bridge board Specifications Model No.: STI-P Interface: 44 pin IDE Suitability: 2.5 SATA HDD Dimension: 69 x 14 x 17.5 mm (L x W xH)

hi pc-PC Small IDE to SATA Adapter Converter Card Compliant with Serial ATA 1.0 Description Contact us Payment method Shipping Policy Return Warranty Reply Feedback Features:1. Convert IDE to SATA device equipment 2. Master-slave mode switching 3. Support the use of 2 adapters (ATA / IDE devices) on the same ATA / IDE channel 4. Compliant with Serial ATA 1.0 5. 48-bit sector addressing 6. Parallel ATA 7. Ultra ATA/133 parallel interface 8. Serial ATA connectors 9. Signal + Power Female Connecto

IDE Controller to SATA Adapter - Use a SATA Drive on a IDE Controller! Use your IDE Controller to connect a SATA device! Featuring the Jmicron 20330 chipset, this device allows you to connect a SATA device to an IDE controller on your motherboard. It's compliant with ATA/ATAPI UDMA transfer up to UDMA 133 and supports SATA/150 drives. A jumper switch allows you to set this to master or slave depending on your needs. You can connect a SATA drive to any motherboard! This adapter is ideal for legacy boards but can also come in handy with newer motherboards. Buy a second adapter and you can set your SATA devices as master and slave on one IDE controller! General Features: Uses an IDE controller to connect SATA devices Jmicro 20330 chipset Serial ATA 1.0a specification compliant Supports... Less

Cables Unlimited USB 2.0 to IDE & SATA Adapter Cable with Power Turn any SATA or IDE drive into a convenient external drive with our USB 2.0 to IDE drive adapter. Simply connect an IDE drive, plug the USB to IDE adapter into an available USB port to transfer files from computers or notebooks, back up files, or store files on hard drives with ease. Supports Iomega Zip, CD-ROM, CD-RW, DVD-ROM and hard drives. Transfer files quickly and easily. Support SATA spread-spectrum transmitter Compliance with USB 2.0 (Hi-Speed) specification Support ATA/ATAPI LBA48 bit addressing mode Support dual LUN (Logic Unit Number) with automatic master/slave enumeration High-Speed Data Transfer, Low Power Consumption Small enough for travel Operating System Support: Desktop and Laptop computers with... Less

The PATA2SATA3 is a bi-directional SATA IDE adapter/converter that lets you connect a Serial ATA drive to a legacy IDE port, or an IDE drive to a SATA motherboard port. A cost-effective solution for upgrading existing IDE systems to support SATA hard drives or optical drives, the SATA/IDE adapter eliminates the expense of having to purchase a controller card while saving the expansion slot that would be required for card installation. In addition to SATA hard drive installation, the adapter can be reversed in order to connect older IDE drives to a newer SATA-enabled motherboard, making it easy to retrieve old files from a previous system.

Digital Scales 2 IN 1 IDE TO SATA/SATA TO IDE Converter Adapter Red 3. supports standard ATAPI, ATA/133, ATA/100, ATA/66, ATA/33.EIDE. 4. Supports standard IDE storage devices (such as Hard Disk, DVD, DVD-RAM, CD-ROM, CD-RW ...) 5.Standard SERIAL ATA specifications and supports mass storage devices (Decided by the main board ),can be used with various types of machinery Specification: One 40pin IDE port One Serial ATA port One 4pin power connector Converts Parallel ATA to Serial ATA 1 x IDE TO SATA Or SATA TO IDE Adapter Red

Type: IDE to SATASpecification s: Connects up to two (2) SATA hard drives or optical drives into an IDE controller and eliminates the incompatibility between IDE and SATA devices in one easy step Uses dual Marvell bridge chipsets for best performance & compatibility Supports all SATA-I SATA-II and SATA-III devices; 2.5' 3.5' & 5.25' HDDs SSDs or ODDs Easily fits in any available IDE (ATA 40-pin) connector in cable free configuration (*no IDE cable required) Supports PIO Mode 0-4 Supports ATA Host Bridge Supports Serial ATA Power Save mode Plug-N-Play and Hot-swapping capability Operating System Requirements: 32-bit & 64-bit Windows 98SE/ME/2000/Serv er 2003/XP/Server 2003/Vista/Server 2008/Windows 7 Linux Mac OS X 10.2.x or abovePackage Contents: One (1) IDE to Dual SATA... Less